Performance Trends

for pictures and an overview of our DataMite USB data loggers
for DataMite 4 Prices
for DataMite III Prices
for Dynamometer Controller Prices
for DataMite Mini Prices
for DataMite Mini Weather Station and Other Weather Options
for RPM, Speed, GPS Sensors and Accessories:
for Temperature Sensors and Accessories:
for Torque, Force, Pressure, Flow Sensors and Accessories:
for Position, Length, Switch, Digital In/Out Sensors and Accessories:
for A/F (wide band oxygen or Lambda) Sensors and Accessories:
for Miscellaneous DataMite Accessories:
for various Package Prices

(DataMite 4 logger "box only" with 10 thermocouple channels, weather sensors and fan, digital in/out connector, GPS connector and vehicle SD memory card)

DataMite 4 USB Prices and Options: to return to top

Part #	Picture	Description	Sug Retail
DT4-DS		DataMite 4 USB Inertia Dyno System (everything needed to measure dyno RPM and calculate corrected torque and HP vs RPM curves). It includes: DataMite 4 USB with 4 RPM channels and 12 analog channels, plus 3 potential weather channels, 10 potential thermocouple channels, 4 digital input channels, and 2 user programmable digital output channels. Dyno RPM sensor, harness and magnets Engine RPM tach input Power supply voltage measurement USB communications cable 50 Hz sampling rate Basic Dyno DataMite Software	$ 899
DT4-DRS		DataMite III USB Drag Race System. It includes: DataMite 4 USB with 4 RPM channels and 12 analog channels, plus 3 potential weather channels, 10 potential thermocouple channels, 4 digital input channels, and 2 user programmable digital output channels. 3 axis accelerometer Battery power voltage measurement Engine RPM tach input Driveshaft RPM sensor and harness and magnets USB communications cable 1 Gig SD memory card Lighted Start/Stop logging switch 50 or 100 Hz sampling rate Basic Drag Race DataMite Software	$ 899
DT4-DRS		DataMite III USB Road Race/Circle Track System. It includes: DataMite 4 USB with 4 RPM channels and 12 analog channels, plus 3 potential weather channels, 10 potential thermocouple channels, 4 digital input channels, and 2 user programmable digital output channels. 3 axis accelerometer Battery power voltage measurement Engine RPM tach input USB communications cable 1 Gig SD memory card Lighted Start/Stop logging switch GPS enabled for optional DT3-GPS 50 or 100 Hz sampling rate Basic Road Race/Circle Track DataMite Software	$ 899
DT4-TC10		10 Internal K Thermocouple channels	350
DT4-DITB		Digital Input Trans Brake cable (to trigger vehicle Acceleration Response timer)	80
DT4-DIBC		Digital Input 4 Switch Breakout Cable	55
DT4-DIL		Digital Input Switch Lead (to be wired by user)	19
DT4-DOH		Digital Output Harness for 2 outputs, 10 ft leads	45
DT4-DOR		Digital Output Relay for DT4-DOH (includes cable/driver) rated for 20 amps, up to 220 volts, AC or DC	50
DT4-DOL		Digital Output RED LED for DT4-DOH, ideal for shift light, warning light, etc. Other colors and options available	40
DT4-DOLB		Mounting bracket for DT4-DOL (2 mounting holes)	10
DT4-DTC		Digital Input/Output T cable, allows combining 2 digital cables to the 1 digital connector on DataMite 4 box.	10

(DataMite III/DataMite 4 Pro inertia kart dyno package)

DataMite III USB Prices and Options (some apply to DataMite 4 also): to return to top

Part #	Picture	Description	Sug Retail
DT3-DS		DataMite III USB Inertia Dyno System (everything needed to measure dyno RPM and calculate corrected torque and HP vs RPM curves). It includes: DataMite III USB with 3 RPM channels and 8 analog channels, plus 3 potential weather channels and 4 potential thermocouple channels. Dyno RPM sensor, harness and magnets Engine RPM tach input Power supply voltage measurement USB communications cable 50 Hz sampling rate Basic Dyno DataMite Software	$ 699
DT3-DRS		DataMite III USB Drag Race System. It includes: DataMite III USB with 3 RPM channels and 8 analog channels, plus 3 potential weather channels and 4 potential thermocouple channels. 3 axis accelerometer Battery power voltage measurement Engine RPM tach input Driveshaft RPM sensor and harness and magnets USB communications cable 1 Gig SD memory card Lighted Start/Stop logging switch 50 or 100 Hz sampling rate Basic Drag Race DataMite Software	$ 699
DT3-DRS		DataMite III USB Road Race/Circle Track System. It includes: DataMite III USB with 3 RPM channels and 8 analog channels, plus 3 potential weather channels and 4 potential thermocouple channels. 3 axis accelerometer Battery power voltage measurement Engine RPM tach input USB communications cable 1 Gig SD memory card Lighted Start/Stop logging switch GPS enabled for optional DT3-GPS 50 or 100 Hz sampling rate Basic Road Race/Circle Track DataMite Software	$ 699
DT3-AF1		Single A/F Sensor (no gauge)	259
DT3-TC4		4 Internal K Thermocouple channels (also available for DataMite 4)	200
DT3-BCA3		2 ft 3 channel analog breakout cable	45
DT3-BCA5		2 ft 5 channel analog breakout cable (also available for DataMite 4)	55
DT3-GPS		External fast responding GPS (global positioning) sensor for lap timing and track mapping (also available for DataMite 4)	349
DT3-LSA		Land & Sea Torque Arm Connector Kit with bridge resistors	245
DT3-IWS		Internal Weather Station Sensor and Fan (also available for DataMite 4)	195

(DataMite Mini Basic Dyno Package DMM-IDP)

DataMite Mini USB Prices: to return to top

Part #	Picture	Description	Sug Retail
DMM-IDP		DataMite Mini Inertia Dyno Package (everything needed to measure dyno RPM and calculate corrected torque and HP vs RPM curves). It includes: DataMite Mini USB with 2 RPM channels and 2 analog channels. Dyno RPM sensor and harness and magnets USB communications cable Basic Dyno DataMite Software	$ 499
DMM-BCT		15 ft Dual thermocouple breakout cable	35
DMM-BCA2		2 ft dual analog breakout cable	35
DMM-IWS		Internal Weather Station Sensor and Fan	195
DMM-IPUHU		Upgrade of the standard BB2-RPML cable with magnet RPM sensor to be able to plug in DTM-IPU Inductive Pickup (DMM-RPMC)	30

DataMite Mini Weather Station and Other Weather Options: to return to top

Part #	Picture	Description	Sug Retail
DMM-WS		DataMite Mini USB Weather Station Package (everything needed to measure weather and make calculated changes to your engine). It includes: Datamite Mini USB Weather Station USB communications cable Weather Wiz Weather Station Software	$ 350
DRP20CD		Optional Drag Race Analyzer Pro Software	$ 229
DRP20CD-TE		Optional Drag Race Analyzer Pro Team Engineer Software	$ 329
DT3-IWS		Internal Weather Station Sensor and Fan for DataMite III and DataMite 4	195
DMM-IWS		Internal Weather Station Sensor and Fan for USB Mini	195

RPM, Speed, GPS Sensors and Accessories: to return to top

Part #	Picture	Description	Sug Retail
BB2-RPML		Dyno RPM Sensor and cable, 18 ft	79
BB2-IPUH		Inductive Pickup Harness, 18 ft	65
DMM-RPMC		Combination BB2-RPML and BB2-IPUH with 1 6 pin connector designed for DataMite Mini USB (much cheaper than both cables separately with breakout harness)	95
DTM-BM		2 Std magnets (.7" dia x .2" thick, better for high temperatures)	3
DTM-SM		2 Small, rare earth magnets (.25" dia x .13" thick, nickel plated)	5
DTM-IPU		Inductive pickup signal conditioning for spark plug wire pickup	59
BB2-IPULV		Low Voltage 'inductive pickup' w harness. Needs BB2-IPUH but does not require DTM-IPU.	139
DTM-RPMA		High temp aluminum RPM sensor.	45
DTM-IPUC		Inductive Pickup Clamp provides an convenient way to attach inductive pickup to spark plug wire and signal enhancement over simple DTM-IPUCW. Still requires the DTM-IPU to work.	55
DTM-IPUCM		Mini (smaller size), metal Inductive Pickup Clamp provides an convenient way to attach inductive pickup to spark plug wire and signal enhancement over simple DTM-IPUCW. Still requires the DTM-IPU to work.	75
DT3-RPMTCI		6 ft lead with 4 pin connector to replace Inductive Pickup Box and attach directly to a Tach or Spark output signal from electronic ignition. It comes with a ground clip to ground the engine to the DataMite system and computer. Still requires the inductive pickup harness BB2-IPUH to plug into. Note: Because this grounds the vehicle to DataMite and PC, it could damage the DataMite or PC is some type of "over-voltage" condition happens on the vehicle.	39
DT3-RPMTC		18 ft lead with 6 pin connector to attach directly to a Tach or Spark output signal from electronic ignition and plug into 6 pin RPM connector on DataMite III or 4. It comes with a ground clip to ground the engine to the DataMite system and computer. Note: Because this grounds the vehicle to DataMite and PC, it could damage the DataMite or PC is some type of "over-voltage" condition happens on the vehicle.	59
DTM-IPUCW		Inductive Pickup Clip for "purple wire" provides simple way to clip wire to plug wire. Easily removed if you need to place wire by coil-on-plug or wrap purple wire.	5
DTM-MB		4 "Magnet head" plastic bolts (1/4 20 x 1" bolts)	40
DTM-SRPM2		Stuska (tm) Dyno RPM Adapter with active sensor DT2-ARL added to harness. This mounts between dyno and mechanical tachometer cable. For smaller Stuska dynos with 1.2" spacing between bolt heads. for cover plate option. This disables your mechanical tach, but provides for easier installation of adapter. Part number DTM-SRPM2C for $20 less.	345
DTM-SRPM8		Stuska (tm) Dyno RPM Adapter with active sensor DT2-ARL added to harness. This mounts between dyno and mechanical tachometer cable. For larger Stuska dynos with 1.8" spacing between bolt heads. for $20 cheaper cover plate option. This disables your mechanical tach, but provides for easier installation of adapter. Part number DTM-SRPM8C for $20 less.	355
DT2-ARL		Active RPM sensor with internal magnet (triggers on large, ferrous metal targets) and 15 ft extension lead with Molex Connector (plugs into DT2-RBC). Generally more stable in high vibration installation.	125
DT2-MRL		Active RPM sensor (which triggers on South pole only of magnet targets) and 15 ft extension lead with Molex Connector (plugs into DT2-RBC). Generally more stable in high vibration installation.	125
DT2-RPMR		Reflective Optical RPM Sensor. Triggers on reflective tape target about 1/2 inch in diameter, from distances up to 30" away. Has alignment beam and signal indicator LED.	259
DT3-LSRA		Land & Sea RPM Adapter, lets our DataMite loggers read the standard Land & Sea RPM Sensor. Using this adapter you can continue to use the RPM sensor already installed on your Land & Sea dyno.	95
DT4-RSF		SuperFlow RPM Adapter and signal conditioner, lets our DataMite loggers read the standard SuperFlow RPM Sensor. Using this adapter you can continue to use the RPM sensor already installed on your SuperFlow dyno. It turns your 60 pulse/rev SuperFlow signal into a 3 pulse/rev signal for our DataMite.	249
DT3-RPMR		Reflective Optical RPM Sensor. If triggering on black/white target it must be within 0.1". If triggering on a tab target, it can be up to .75" away from target. Click "Click Here" for picture. NOTE: This sensor runs on 5 volt power and may require special, extra cost cabling depending on which connectors are available on your DataMite III or DataMite 4.	69
DTM-RPMO and DTM-RPMOC		Slotted Optical RPM Sensor and Cable. This sensor is commonly used on RC (radio controlled) engine inertia dynos.	75 and 35
DT3-MAG		Magneto signal conditioning box, hooks to kill switch of magneto. Must be wired in by customer.	99
DT3-MAGC		Magneto signal conditioning box, hooks to kill switch of magneto. Includes cabling to plug into standard DataMite loggers and cabling.	175
DT4-OT		Hand held optical tachometer with display. Works great for checking RPM signals reported by DataMite loggers. Reads reflective tape placed on spinning component, but does not connect to a logger or log data itself.	30
DT3-GPS		External fast responding GPS (global positioning) sensor for lap timing and track mapping (also available for DataMite 4)	349

Temperature Sensors and Accessories: to return to top

Part #	Picture	Description	Sug Retail
DT3-TC4		4 Internal K Thermocouple channels (also available for DataMite 4)	200
DT4-TC10		10 Internal K Thermocouple channels	350
DTM-AK		K Thermocouple for air temp with 16 ft lead	39
DTM-C0K		K Thermocouple for 10mm spark plug w 6 ft lead	78
DTM-C2K		K Thermocouple for 12mm spark plug w 6 ft lead	78
DTM-C4K		K Thermocouple for 14mm spark plug w 4 ft lead	59
DTM-C4K18		K Thermocouple for 14mm spark plug w 18 ft lead	79
DTM-EKL6		K Thermocouple 6 ft extension cable	35
DTM-EKLC		K Thermocouple custom length extension (over 10 ft $45, over 20 ft, $55)	35
DTM-EKB		1/8" FPT Thermocouple weld-able boss	3.00
DTM-EKBHD		1/8" FPT Thermocouple heavy duty weld-able boss	3.50
DTM-EKF		Thermocouple 1/8" steel exhaust compression fitting	9.90
DTM-EKBP		Thermocouple 1/8" weld-able boss plug	3.00
DTM-EKFF		Thermocouple 1/8" fluid compression fitting (neoprene O rings)	9.90
DTM-EKC		Hose Clamp Style Exhaust Thermocouple Mounting Kit	12
DTM-EKE		K Exhaust Thermocouple (E for exposed tip, fast response) 3" probe, 4 ft lead	70
DTM-EKE10		K Exhaust Thermocouple (E for exposed tip, fast response) 3" probe, 10 ft lead	80
DTM-EKE18		K Exhaust Thermocouple (E for exposed tip, fast response) 3" probe, 18 ft lead	85
DTM-EKS		K Exhaust Thermocouple (S for sheathed tip, fluid temps) 3" probe, 4 ft lead	70
DTM-EKS10		K Exhaust Thermocouple (S for sheathed tip, fluid temps) 3" probe, 10 ft lead	80
DTM-EKS18		K Exhaust Thermocouple (S for sheathed tip, fluid temps) 3" probe, 18 ft lead	85
DT2-FLTWO		Replacement 150-230 deg fluid temp sensor (special cable required for original installation)	30
DT2-IRA		Infra Red (non contract), std response (2 Hz), analog 0-5 volt tire temperature sensor. Spot size is 40% of distance from target (for example, at 5" from tire, spot is 2" in diameter)	195
DT2-IRAF		Infra Red (non contract), fast responding (10+ Hz), analog 0-5 volt tire temperature sensor. Spot size is 40% of distance from target (for example, at 5" from tire, spot is 2" in diameter)	225
DT4-IR3 DISCONTINUED		3 channel Infra Red (non contract) tire temperature sensor, used primarily for tire temperatures. 3 temperatures can be measured via just one 0-5 volt analog channel. for more info DISCONTINUED	345
DT2-TC4		4 channel K thermocouple amplifier and recorder w power input connector and serial output connector. Other leads are covered with shrink tubing to prevent shorting. for price of typical K thermocouples, DT2-K3.	399
BB2-2KC		Black Box Dual K Thermocouple Converter	190
BB2-BCT		15 ft Dual thermocouple breakout cable	35
DT3-TCE5		5 ft thermocouple extension cable for DTM-III and DTM-4	165
DT3-TCE10		10 ft thermocouple extension cable for DTM-III and DTM-4	180
DT3-TCE15		15 ft thermocouple extension cable for DTM-III and DTM-4	195
DT3-TCE30		30 ft thermocouple extension cable for DTM-III and DTM-4	215

Torque, Force, Pressure, Flow Sensors and Accessories: to return to top

Part #	Picture	Description	Sug Retail
DTM-ILCA		External Load Cell Amplifier	175
DT2-LDC2		"S" Beam Load Cell for measuring force, typically for dynamometer torque, 250 lbs force. Made in USA. Cheaper options available. Lower ranges also available.	550
DT2-LDCx		"S" Beam Load Cell for measuring force, typically for dynamometer torque, 500, 1000 lbs force. Made in USA. Cheaper options available.	695
DT2-LDCx		"S" Beam Load Cell for measuring force, typically for dynamometer torque, 2000 lbs, 3000 lbs force. Made in USA. Cheaper options available.	645
DT2-LDC5		"S" Beam Load Cell for measuring force, typically for dynamometer torque, 5000 lbs force. Higher ranges also available.	895
DT3-LSA		Land & Sea Torque Arm Connector Kit for Small Arm (requires DTM-ILCA amp)	245
DT3-LSAB		Land & Sea Torque Arm Connector Kit for Big Arm (requires DTM-ILCA amp)	295
DTM-SKT		Stuska (tm) Dyno Quick Connects for torque pressure sensor	70
DTMPxxx		Higher accuracy stainless steel pressure sensor (ranges include 30, 50, 75,100, 200, 300, 500, 1000, 2000, 3000, and 5000 PSI). Specify range with xxx in 10s of PSI, for example, DTMP005 is 50 PSI. For pressures of 1000 psi or more, like 1000 PSI, use 1M for xxx).	190
DT4-DP0.3		-0.3 to 0.3 differential pressure sensor with 2 ports (other ranges available of +/- 1.0 and +/- 3.6 psi)	145
DT2-VACP		DT2-VACP Vacuum/Boost Sensor, one port vacuum, the other boost or pressure 36 psi (other ranges higher and lower available)	120
DT2-VACx		Vacuum and Boost pressure sensor, which will measure from 14.7 psi vacuum (30" Hg vacuum) up to X psi of boost pressure, where X can be 3 (30 psi), 4 (45 psi) or 6 (60 psi). This sensor is ideal for measuring intake manifold vacuum and/or boost pressure from supercharging or turbocharging.	190
DT4-MAFL		Mass Air Flow Sensor (large) up to 800 CFM, 4" diameter, low restriction with 0-5 volt output	500
DT4-AFP6		6" Air Flow Sensor via Averaging Pitot Tube, good for up to 3600 CFM. 2700 and 1700 ranges also available. This sensor offers a more compact package for large CFM flow than the DT4-MAFL listed above. (Note: You can purchase an extra sensor for $120 or $150 and switch to a different range.)	465
DT4-AFP4		4" Air Flow Sensor via Averaging Pitot Tube, good for up to 1600 CFM. 1200 and 700 ranges also available. This sensor offers a more compact package for large CFM flow than the DT4-MAFL listed above. (Note: You can purchase an extra sensor for $120 or $150 and switch to a different range.)	425
DT3-FSC		1500 HP (on gasoline) Fuel Flow sensor with RPM output, 1/2" female NPT in and out	999
DT3-FSD		2500 HP (on gasoline) Fuel Flow sensor with RPM output, 1/2" female NPT in and out	999
DT3-FSE		4000 HP (on gasoline) Fuel Flow sensor with RPM output, 1/2" female NPT in and out	999
DT3-FS231		500 HP (on gasoline) Fuel Flow sensor with RPM output	690
DT3-FS20BA		150 HP (on gasoline) Fuel Flow sensor with RPM output.	690
DT3-FFK		Kart Fuel Flow 2.5-18 HP Gas Sensor, RPM output	1099
DT3-FFK4		Kart Fuel Flow 3.6-36 HP Gas Sensor, RPM output	1099
DT3-FFK5		Kart Fuel Flow 9-90 HP Gas Sensor, RPM output	1099
DT4-RPF		Signal Conditioner for Racepak (tm) Fuel Sensor and 15 ft cable and proper connectors, which lets our DataMite loggers read Racepak fuel flow sensors	250
DT3-SFA9		9" Air Flow Turbine fitted into "velocity stack" for mounting on 4 BBL carb, RPM output	980
DT3-SFA9A		9" Air Flow Turbine fitted into "velocity stack" for mounting on 4 BBL carb with adapters for different carb sizes, RPM output	1250
DT3-BLB6		6 CFM Blowby Sensor (other ranges available 0.3, 1, 3, 12 and 18 CFM) 0-5 volt output	649

Position, Length, Switch, Digital In/Out Sensors and Accessories: to return to top

Part #	Picture	Description	Sug Retail
DTM-L1		1.5" Spring loaded linear displacement sensor	85
DTM-Lxx		Linear displacement sensor (Ranges include 4, 5, 6 , 8 and 10 inches movement. Specify ranges with xx, for example DTM-L04 is a 4 inch sensor.) NOTE: Sensor costs increase with length of sensor. 6" and 8" is $325 and 10" is $480	345 (6", 8")
DT2-SL8		Protective sleeve for 8" travel sensor (sleeves for other length sensors also available)	80
DTM-LRE		Replacement rod end	39
DT2-SHM		Universal shock travel sensor mounting kit	28
DTM-SPX		2.8" and 10" Cable Potentiometer (string pot)	359
DTM-SW		Position (on/off) switch with 10 ft lead	35
DT3-STR		Steering sensor to measure steering wheel angle movement	119
DT4-DITB		Digital Input Trans Brake cable (to trigger vehicle Acceleration Response timer)	55
DT4-DIBC		Digital Input 4 Switch Breakout Cable	55
DT4-DIL		Digital Input Switch Lead (to be wired by user)	19
DT4-DOH		Digital Output Harness for 2 outputs, 10 ft leads	45
DT4-DOR		Digital Output Relay for DT4-DOH (includes cable/driver) rated for 20 amps, up to 220 volts, AC or DC	50
BB2-RSW		Hand held On/Off Recording Switch, lets you start and stop recording on Dyno system away from the keyboard. Good for chassis dynos, where driver may need to start/stop recording.	65
BB2-RSWF		On/Off Recording Foot Switch, lets you start and stop recording on Dyno system if you need an extra "hand".	65
DT3-TSW		Lighted, toggle, recording switch for vehicle DataMite III and DataMite 4 logging systems.	55
DT4-DOL		Large .8" Digital Output Red LED for DT4-DOH, ideal for shift light, warning light, etc. Other colors and options available. Fits .7" panel hole.	40
DT4-DOLB		Mounting bracket for DT4-DOL (2 mounting holes)	10
DT4-DTC		Digital Input/Output T cable, allows combining 2 digital cables to the 1 digital connector on DataMite 4 box.	10

A/F (wide band oxygen or Lambda) Sensors and Accessories: to return to top

Part #	Picture	Description	Sug Retail
DT3-AF1		Single A/F Sensor (no gauge)	259
DT3-AF1P		Single A/F Sensor (no gauge) with 110 or 220 VAC power supply and US, Aussie, European, or UK plug	299
DT2-AFG		Single Wide Band UEGO A/F sensor and controller gauge.	299
DT2-AFGP		Single Wide Band UEGO A/F sensor and controller gauge, with 110 or 220 VAC power supply and US, Aussie, European, or UK plug.	349
DT2-AFS		Replacement Bosch Sensor for DT2-AFx,DT2-AFG, DT3-AF1, and DT3-AF4 UEGO systems with earlier, square connector. Click on blue button for a picture.	129
DT2-AFSR		Replacement Bosch Sensor for DT2-AFx,DT2-AFG, DT3-AF1, and DT3-AF4 UEGO systems with later, rounded connector. Click on blue button for a picture.	145
DT2-AFR		Remote sampling system for single DT3-AF1P or DT2-AFGP, requires 110 VAC power. 220 VAC option available.	459
DT2-AFR2		Dual remote sampling system for two DT3-AF1P or DT2-AFGP, requires 110 VAC power. 220 VAC option available.	599
DT2-AFRC		'Exhaust Pipe' clamp which attach to probe(s) of DT2-AFR remote sampling system to easily, quickly clamp probe to exhaust pipe.	65
DT2-AFRV		A/F Remote 220 V Option with Aussie, European, or UK plug	40
DT2-AFRT		A/F Remote Oil Trap Option	60
DT2-AFRM		Mini remote sampling system for DT2-AF1P or DT2-AFGP. Powered by 12 volts DC, which can be plugged into power supply w DT2-AF1P or DT2-AFGP.	339
DT2-AFRMH		Mini remote sampling system Switch Harness plugs into power connector and provides leads for On/Off switch.	12
DT2-AFSB		Exact replacement weldable boss fitting (with shoulder) for DT2-AFS A/F Oxygen sensor	6
DT2-AFSBC		Exact replacement cap for weldable boss fitting DT2-AFSB above	9
DTM-EBS		Oxygen sensor threaded boss fitting to weld to exhaust pipe	3.50
DTM-EBSP		Allen head plug for Oxygen Sensor weld-able boss	2.50
DTM-EBSE		Oxygen sensor threaded boss fitting to weld to exhaust pipe, extended and finned to keep sensor cool and out of flow to keep exhaust free flowing	18
DT2-AFCC		A/F Sensor (UEGO) Calibration Checker.	849
DT3-PLAF		DataMite power lead from A/F power supply, to commonize grounds between A/F system and DataMite for accurate A/F data	35

Miscellaneous DataMite Accessories: to return to top

Part #	Picture	Description	Sug Retail
DT4-OBD2		Dyno DataMite OBD2 Link, requires Enterprise Edition of Dyno DataMite software	59
DT4-DOL		Large .8" Digital Output Red LED for DT4-DOH, ideal for shift light, warning light, etc. Other colors and options available. Fits .7" panel hole.	40
DT4-DOLB		Mounting bracket for DT4-DOL (2 mounting holes)	10
DT3-BCA3		2 ft 3 channel analog breakout cable	55
DT3-BCA5		2 ft 5 channel analog breakout cable (also available for DataMite 4)	65
DTM-LD		Std 10 ft Lead wire with proper connector to plug 0-5 volt analog signal into 4 pin connector on DataMite harness DataMite box. Sensor to be wired by user, schematic included.	25
DTM-LD15		Std 15 ft version of DTM-LD above.	30
DT2-AE5		5 ft analog extension cable with 4 pin connectors on each end, 1 male and 1 female	28
DT2-AE10		10 ft analog extension cable with 4 pin connectors on each end, 1 male and 1 female	30
DT2-AE15		15 ft analog extension cable with 4 pin connectors on each end, 1 male and 1 female	35
DT2-AE20		20 ft analog extension cable with 4 pin connectors on each end, 1 male and 1 female	38
DT2-RE15		15 ft RPM extension cable with 6 pin connectors on each end, 1 male and 1 female	32
DT2-RE25		25 ft RPM extension cable with 6 pin connectors on each end, 1 male and 1 female	39
DTM-LDR		Std 10 ft Lead wire with proper connector to plug RPM signal into 6 pin connector on DataMite harness DataMite box. Sensor to be wired by user, schematic included.	27
DTM-LDR15		Std 15 ft Lead wire with proper connector to plug RPM signal into 6 pin connector on DataMite harness DataMite box. Sensor to be wired by user, schematic included.	32
DT2-USB		USB to Serial Port Adapter. Adapts a computer's USB port to Serial (COM) so the computer can read the DataMite's serial data.	39
DTM-PS		110V AC to 12 VDC (unregulated) power supply (barrel connector).	15
DTM-PSU		110VAC/220 VAC regulated 12 VDC power supply (barrel connector) UPGRADE from DTM-PS with 4 different plugs for different countries.	24
DT3-OI		DataMite (4/III/Mini) USB Optical Isolator 4000 v max	175
DTM-BP		Rechargable battery pack with recharger (approx 6 hours of recording time).	45
DTM-205		10 ft lead with 0-20 volt to 0-5 volt converter (other voltage ranges available)	35

Controls and Actuators: to return to top

Part #	Picture	Description	Sug Retail
DT4-EC		DataMite Eddy Current 200 HP control	1099
DT4-EC2		DataMite Eddy Current 220 VAC Option	175
DT4-WBC		DataMite Water Brake control	1599
DT4-WBCS2		SF Water Brake Actuator Mod, Generation 2	699
DT4-THC		Electronic Throttle control	1299
DT4-THCC		Electronic Throttle control, clevis end	35
DT4-THCBJ		Electronic Throttle control, ball joint end	35
DT4-MTC		Mechanical Throttle control cable kit	480
DT4-MTCE		Mechanical Throttle control cable extension	190

Many of the standard DataMite sensors are compatible with the DataMite II, Black Box II, and DataMite USB III or Mini. The price may be slightly different when used on different loggers. Lead lengths are typically 15-18 ft long. If you need special length leads, we can customize the lengths for a nominal charge.

Data loggers have a limited 1 year warranty.

Package Prices to return to top

DataMite Mini USB Basic Inertia Dyno Package (typically for small engines) ( for picture)